220V/60HZ 105CFM Refrigerated Compressed Air Dryer for 30 HP Air Compressor

Description: Industrial Refrigerated Compressed Air Dryer 105 CFM 230V/60HZ/1-Phase for 30HP Rotay Screw Air Compressor Model:SE-30AAir Capacity: (105CFM）Output Pipe Diameter: NPT 1 "Working Operating pressure: 0.7-1.0MPaCooling: By AirInlet temperature:<45℃Ambient temperature: < 40℃Pressure dew point: 3-10℃Power supply:220V/60HzRefrigerant type: R407CPower consumption: o. 88 KWAir Flow： 105 CFMWeighat: 133 lbsPackage size:27*20*32 inch GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION: 1. This equipment is a pressure-containing device. Don’t exceed maximum operating pressure as shown on equipment serial number tag.2. This equipment requires electricity to operate. Install equipment in compliance with national and local electrical codes.3. Disconnect power supply to equipment when performing any electrical service work. READ PRIOR TO STARTING THIS EQUIPMENT:1. This equipment has been thoroughly checked, packed and inspected before leaving out plant2. This equipment is shipped to accommodate a forklift truck. When installing this equipment, move it by means of a forklift. Never lift it by hooking on to the air inlet and outlet connections.3. Air-cooled units – Free air flow - Ambient air should be free to flow across the refrigeration condenser. Do not block either side of the cabinet. Leave at least 1.5m clearance for free airs flow. The ambient temperature is to be within the operating parameters of 2C to 38C Function:Compressed air enters the air-to-air heat exchanger and is pre-cooled by the chilled outgoing air. The air then enters the air-to-refrigerant heat exchanger where it is further cooled by the refrigeration system. As the air is cooled, water vapor condenses into liquid droplets. The air and entrained water droplets then enter the separator where liquid water is removed. In addition, the air is filtered of all solid particles three microns and larger. Clean, dry compressed air leaving the dryer minimizes maintenance and repair of pneumatic distribution, instrument and control, and actuation devices, reduces product contamination, and increases productivity. Mounting:1. A dry, well-ventilated area is the best location for installation of the dryer. It also should be in an area where the ambient temperature will not exceed 40C or fall below 2C.2. A dryer should be kept at a distance from the air compressor in order to prevent the vibration of the compressor from interfering with the dryer’s operation.3.Mount dryer on firm level surface.4.Automatic drain outlet should be connected to the plant drainage system in order to prevent condensate from polluting plant.5. For typical placement in a compressed air system, see drawing back. Power and electrical connections:1. Be sure that voltage to unit is as marked on unit serial number tag.2. Range of voltage fluctuation will not exceed 10% of rated voltage.3. Electrical entry in through electrical connection entry hole in electrical enclosure. Connect power to proper terminals.Notice proceeding1. Note running of the refrigeration compressor. Check and remove troubleshooting in time.2. Don’t start-up and shutdown frequently, dryers should restarted after 10 minutes.ShutdownClose air inlet valve, then press STOP button and cut off power. MAINTENANCEAir-cooled condenserAmbient air should be free to flow across the refrigeration condenser for heat exchanging. Do not locate the dryer in direct sunlight. Air-cooled condenser should be cleaned with compressed air periodically.Automatic condensate drainMonthly flush out accumulated sludge and dirt in the automatic condensate drain. Procedure for clean drains:a. Close manual valve ahead of drain.b. Depressurize drain by loosening shell bolt.c. Remove shell bolt and detach the shell, take filter core out and clean it with brush and water.d. Reassemble the core and the shell. Then open the manual valve ahead of drain.Electric apparatusCheck parts in the electric apparatus box and removes troubleshooting in time. On Sep 1, 2024 at 20:46:46 PDT, seller added the following information:

Price: 1399 USD

Location: Azusa, California

End Time: 2024-10-02T03:27:08.000Z

Shipping Cost: 0 USD