3 inch Alcohol Distiller Bubble Plate Reflux Column & Condenser, Fits Tri Clamps

Description: Clamps right to anything with 3" tri clamp. (link to 3" adapter below if needed)The Still Includes4 section bubble plate column as pictured (Note: glass sections attach with a silicone gasket now, no stainless ring between them for a better seal and lower cost)ThermometerStainless Steel Inline condenserAll necessary gaskets and clamps (2x2" clamps and 1x3" clamp included)Spare borosilicate glass section included, we also carry all the spare parts if ever needed2 spare silicone gasketsProduct DetailsLight assembly required. No soldering needed. Super fun to use and easy to clean.100% Food Grade 304 Stainless Steel and T2 lead free food grade copper.2-piece reflux column / condenser that completely disassembles for easy storage.It's a highly efficient bubble plate column still.It can be used to distill ethanol (fuel alcohol), spirits (whiskey, Bourbon, vodka, gin, tequila, "moonshine," and more), and essential oils.Compatible with electric hot plates.Compatible with propane turkey fryers.Compatible with anything with 3 inch tri clampComplete crystal reflux still column with copper bubble plates. Ideal to fit any boilers, beer kegs that have 2" tri clamp just need a 2" x 3" reducer fitting put on top. The system is made of Durable Easy-to-clean stainless steel 304 and t2 lead free copper which is a guarantee for a lifetime of use. The glass design will allow you to view the entire distillation processes from the start to the end. This will definitely be an eye catcher in your distillery. So fun to watch! 3" tri clamp bottom flanges are made to clamp to any 3" tri clamp opening! We also sell adapters to make it fit the top of the Robobrew, Grainfather, Turboboiler, Mash and Boil or any lid with a 17mm hole. Want to clamp it to a beer keg or anything with 2" tri clamp? We have the adapter here https://www.ebay.com/itm/284633400695 3 in. x 2 in. - ForgeFit® Stainless Tri-Clamp Concentric Reducer - Brewing NOTE: Glass sections connect with special slotted silicone gaskets now, much better and safer than the stainless rings shown in the picture which were expensive and cracking the glass. How The Bubble Plate Column Works:Vapor will come into contact with the plates and caps inside the column, causing the vapor to condense back into a liquid. This will happen at the very top of the still where the RC cooler will knock that vapor back into a liquid, causing a reflux action. As the liquid then falls down from bubbler cap to bubbler cap, the liquid that falls is eventually forced back up through the plates again. This process of being forced to run through the caps and plates multiple times creates an end product that has essentially been distilled multiple times in a single run, meaning you can get higher proof alcohol when compared to an empty column. The bubble plates perform a similar function as the copper packing in a hybrid column, but does so more efficiently. When running a bubble plate column, the first run will start in the range of 72.5%-85%. Depending on the quality of the wash, you can reach up to 95%-96% ABV, the highest-grade ethanol you can distill. Please note: There is no instruction manual. This is deemed a commercial unit for those with a license to produce alcohol. We take no responsibility for your failure to comply with your state/local legislation. Keywords: alcohol distiller, vodka still, whiskey still, moonshine still，distillation column，distillation equipment，home alcohol distiller，flute still，copper still. Assembly Instructions: Items needed for assembling the four 3 inch glass column with copper bubble plates:4* glasses2* stainless steel flanges4*copper bubble downcomers with caps4*glass gaskets4*stainless steel rods with nuts Step 1Put the copper bubble caps on the copper downcomers to get them connected together, and then put the complete copper bubble plates into the glass gaskets, the final part of this step is to put them on one of the flanges, as following: see picture for "step 1" in images aboveStep 2 Put one of the glasses on the glass gasket that is put on the flange, then put the complete copper bubble plates into the glass gasket again and put them on the top of the first glass, as following: see picture for step 2 in images above.Step 3Repeat the Step 2( put the complete copper bubble plates into the glass gasket again and put them on the top of the next glass) till we use all the glasses. As following: See picture for Step 3 in images above.Step 4Put the flat gasket on the top of the final glass, and then put the rest flange on the top of the flat gasket. Step 5By using all the rods and nuts to get the column tight. That’s all.

Price: 300 USD

Location: Lansing, Michigan

End Time: 2024-11-19T19:17:49.000Z

Shipping Cost: N/A USD