3M Double Face Sided Tape 15mm 3 Meters for car LED Light Weather Shield Panel

Description: This auction is for 1 roll 15mm width* 3 meters length 3M 5108 Double Sided Tape Notices: did not move it until 72 hours, it can be strongest adhesion after 72 hour. Specification Brand: 3M Model: 5108 Width: 15mm Length: 3 Meters Thickness:0.8mm Color: Gray Condition: Brand New Temperature Resist: 120C Features Brand New and High quality. Typical applications include body side moldings; stainless steel, ABS and PVC rocker panels; wheel lip moldings, door edge moldings, nameplates/ ornamentation, luggage rack slats, wind and rain de ectors, and dashboard overlays. Strong adhesion to automotive substrates. Weather and car wash resistant. Confortable. Can be used on textured surfaces, such as painted cement or brick. High-strength core maintains a thin, consistent bond line. Instructions for use:Cleaning has been posted to the site, keep dry; The red rubber adhesive peeled off, under normal circumstances, while paste slowly, while evenness tools, while exposing the adhesive If the tape length is less than 10cm, red gum all tear off the paste. But must be careful not to accident adhesions or fall to the ground sticky from the dust; After paste is moderately hard to squeeze, according to 3M Adhesive properties, in 24Hours without car wash. Remark ** Inital adhesive is not good, please keep more than 24 hours after adhesive. It can get excellent performance when using with 94 #. ** If temperature lower than 15C, please work with hot blower ** Please be sure the surface clean 100% How to use this tape?Clean:For maximum bond strength,the surface must be clean, dry, smooth, have no rust and oil pollution.Typical cleaning solvents are heptane or isopropyl alcohol.Pressure: Pressure on the adhesive and the surface can help improve bond strength,roller or platen can be used.Time: After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hoursand 100% after 72 hours.Temperature:Ideal application temperature range is 70°F to 100°F (21degree centigrade to 38degree centigrade).Operating temperature should not be below 10 degree centigrade, the temperature is too low, will lead to cure time longer. If temperature is too low, move material and adhesive tape into the warm indoor storage or heating treatment. Q. What percent of the final bond strength can I expect immediately after application? After 24 hours? After 72 hours?A. Immediately after an application is made, about 60% of the bond strength is achieved. As the adhesive continues to wet-out the surface, you can expect the bond to be at about 75% - 80% after 24 hours. After 72 hours, 95%+ of the bond strength is achieved. The bond will continue to build with time.Q. Is the tape solvent resistant?A. Yes, 3M acrylic foam tapes are resistant to most common automotive solvents like gasoline, diesel fuel, washer solvent, etc. Solvent resistance is a function of type of solvent, time of exposure and temperature.Q. Why doesn`t the tape feel sticky?A. 3M`s high performance acrylic adhesives tend to be firm and dry to the touch. They are designed to bond materials other than skin. The adhesives used are designed to give optimum performance and adhesion to automotive substrates and components. The natural oils and moisture of skin can vary from person to person and affect the "thumb appeal" of the 3M Acrylic Foam Tape. To one person the tape can feel very sticky and to another it can feel much less sticky to the touch. The difference in "thumb appeal" is in the variation of the 2 individual`s skin surfaces not the adhesive.Q. The part is not adhering to the vehicle. What might be wrong?A. Areas to investigate for poor adhesion or performance include:Check for surface contamination. The substrates must be clean and free of any contaminant. This is the most common cause of poor adhesion.Check for surface match. Are the two surfaces to be bonded a good match?Check for proper application pressure and wet-out.Check the back of the component for flatness.Check the installation process for proper procedures. Payment Shipping Return Feedback

Price: 4.72 USD

Location: 深圳, 廣東省

End Time: 2024-08-14T05:17:06.000Z

Shipping Cost: 3 USD