4.3" V2 NanoVNA-F VNA Vector Network Antenna Analyzer UHF HF VHF 50KHz-3GHz

Description: 【Upgrade】NanoVNA-F V2 is based on the latest firmware upgrade to 0.4.0 NanoVNA-F and uses 4.3-inch IPS TFT LCD screen, 800 x 480 resolution, so you can see clearly even in outdoor bright light, and you can measure S parameters, voltage VSWR(SWR), phase diagrams, group delay, Smith circles, polarity, linears, etc [Improved Frequency Range] The measurement range of the NanoVNA-F V2 is extended to 50KHz - 3GHz (previous version measurement range is 10KHz-1.5GHz), and the TX/RX method can fully measure S11 and S21 parameters with the output signal harmonic extension from the clock chip SI5351 (5,000 mAh High Capacity Battery) The NanoVNA-F V2 is equipped with a 5,000 mAh high capacity battery that can be used for charging Android phones and tablets, with an extended USB port, built-in 5 V output, and it can be used to charge Android phones and tablets, and uses a 2A large current charging IC to shorten the charging time Aluminum Alloy Design: All aluminum alloy shells, durable, electromagnetic interference, accurate measurement and RF interface for SMA and easy to connect various types of measurements, protecting it from the elements Package Includes: 1 x NanoVNA-F V2 main unit, 2 x SMA-JJ RG405 connection cable, 1 x calibration part, 1 x 50 ohm standard load, 1 x open calibration part, 1 x short calibration part, 1 x SMA-F double head hole, 1 x SMA elbow external screw inner pin - 1 x TYPE-C cable Product description The NanoVNA-V2 portable vector network analyzer is based on 0wOComm's S-A-A-2 design, leading upgrades performance in the new generation of product is expanded to 50kHz-3000MHz, which has a larger dynamic range and reached 80db UV band frequency duplexer, more accurate, more practical, flexible and faster operating - interface measurements. This small vector network kills the performance of all versions of this NanoVNA series on the market. You can test antenna VSWR impedance, filter insertion loss, isolation, VSWR, cable attenuation, shortening coefficient, phase, antenna amplifier, frequency meter, cable length, group delay, and most importantly, it can be used for debugging UV band frequency duplexers, which is highly recommended and kills any other version of the NanoVNA on the market. Highly recommended!Product Performance1. Measurement Frequency Range: 50KHz-3000MHz.2. RF output power: -9dbm (error in 1GHz: positive or negative 1db)Frequency Accuracy: <0.5ppm4.S21 Dynamic Range: 70dB (1.5GHz), 60dB (3GHz)5.S11 Dynamic Range: 50dB (1.5GHz), 40dB (3GHz)6.2 ports/return loss: 20dB type (1.5GHz), 13dB min (3GHz).7. USB interface: USB Type-C communication mode: CDC (serial)8. Number of calibration points: 101 pt.9. Number of scanning points: 101 pt.10. Display trace: 4 traces11. Markers: 4 pcs (marker bar can be moved up and down on the screen)12. Saving Setting: 5 (after saving, it needs to be marked from new.You can call it directly when you turn on the next time, and automatically call the saved parameters before the last power off when you turn on the next hour.)13. Scan time: about 1.9s/1 hour (50kHz~3000MHz full band)14. Can measurement S parameter, voltage VSWR SWR Smithsonian circle phase diagram, group delay, ... ;;...5. 4.3 inch IPS LCD screen, close to 180° IPS TFT (800x480) viewing angle, long time use does not hurt the eyes; 16. The use of aluminum alloy chassis is is better than 80dB dynamic range, effectively shielding electromagnetic interference 17. Compact design, body size 125mm x 75mm x 20mm, compact and portable.18.SMA RF interface, easy to connect all kinds of test pieces.19.5000mAh high capacity lithium battery, battery life up to 7 hours.20. Full touch screen design supports three side buttons while providing flexible and convenient operation.21. Support Chinese and English menu switching.Footprint22. Support screen brightness adjustment.23. Firmware upgrade by virtual USB flash drive, no programmer required, F22. Extend USB power output interface, 5V/1A output (can be used as a rechargeable treasure); Top 24. Use high current 2A charging IC, short charging time;25. Support the top computer, you can use the computer as a display interface.26. Weight with plastic box: 400gProduct Standards1 x HostSMA-JJ RG405 Connecting Cable 20CM x2 (NanoVNA-V2 is a standard SMA female interface, external screw and internal hole.Holes,) 1 set of calibration parts (50Ω standard load, 1 open circuit calibration part, 1 short circuit calibration part, and the included calibration parts, the measuring instrument can be calibrated to get good measurement results data, if you change the measurement conditions such as the addition of adapter line, change frequency range, parameters are stored in 0-4, all parameters can be called through "callback" function. All parameters can be called through the "callback" function, if the requirements are not very tight, you can perform full-band calibration work, and can also be used to change the frequency range, but at this point there is a certain degree of error).1 x SMA-F Double Header Hole (also known as SMA Female Double Pass)1 x SMA elbow from inner screw hole1 x Type-C cable1 x StylusAt the same time, it is made of pearl cotton to protect your instruments and components, and comes with a set of packing boxes.

Price: 104.99 USD

Location: ShenZhen、Guangdong

End Time: 2024-11-06T15:17:39.000Z

Shipping Cost: 0 USD