Description: MAX CLR A/BCLEAR LIQUID RESIN(24 Fluid Ounces Combined Volume) 1 Pint Of MAX CLR PART A -Resin And 1/2 Pint MAX CLR PART B -Curing AgentProduct Description MAX CLR A/B is a two-component epoxy resin system that is produced in compliance with FDA regulations intended for direct food contact coatings and adhesive applications. MAX CLR A/B is thermoset polymer resin that cures crystal clear and demonstrates high chemical resistance to acidic and basic compounds. It is resistant to dilute grain alcohol and can withstand brief contact with hot fluids (up to 187 °F) such as coffee, tea, and soups.The primary purpose of the MAX CLR resin system is to facilitate a sanitizable coating that demonstrates low extractable of its chemical constituents during direct food contact. Equally, the objective goal of the cured coating is to create a durable barrier. When applied onto a porous substrate (such as wood) the cured coating prevents absorption of fluids or organic compounds that allows bacterial colonization or microbial growth. PHYSICAL AND MECHANICAL PROPERTIESViscosityDensityForm and Color800 – 1,200 cPS @ 25°C Mixed1.10 g/ccClear Transparent LiquidMix Ratio100 Parts to 50 Parts A By Weight or by Volume 2:1 (Part A to Part B)Working Time45 Minutes @25°C (77°F 100-gram mass)Peak Exotherm70°C (158°F, 100-gram mass)Handle TimeFull Cure Time5.5 Hours36 Hours minimum @ 25°C (75°F)Hardness72± 5 ShoreTee-Peel Strength5.7 Lbs per inch WidthTensile Shear Strength1,300 psi @ 25°C (77°F) 800 psi @ -80°C (-112°F) 550 psi @ 100°C (212°F)Elongation9.0% @ 25°C (77°F)Compressive Strength2,200 psiHeat Distortion Temp80°C (176°F)All components used to formulate the MAX CLR resin system are listed in the Code of Federal Regulations, Title 21, Part 175 for resinous coatings/adhesive subject to direct and indirect food contact.IMPORTANT GUIDELINES FOR FOOD CONTACT APPLICATIONS For food contact applications, MAX CLR A/B must be fully cured to ensure no chemical leaching can occur when foodstuffs' come in contact with the cured resin system. Any uncured chemical compounds caused by improperly prepared MAX CLR may be extracted and cause cross-contamination or leaching during food contact. Please review the following and to avoid any curing problems.COLD TEMPERATURE CRYSTALLIZATION The high purity nature of the resin formulation makes it prone to crystallizing when exposed to temperatures below 57 °F. During the colder season, the MAX CLR PART A resin component may crystallize during shipping. It can also occur after the container has been stored in an uncontrolled environment. Crystallized resin appears as an opaque white mass on the bottom of the bottle. See instructions and video below. PROCESSING With the cap securely in place, place the PART A container in a hot water bath (160°F) until the contents are revert back to its liquid state and optically transparent. Cool the PART A bottle to 75 def F and the mix the proper amount of PART B curing agent.STORAGE Secure caps for both bottles and store above 65°F minimum temperature to prevent re-crystallization The resin system will remain viable for at least 12 months or longer. USE AND APPLICATION Precondition both bottles to 75°F and measure the components accurately at a 2:1 mix ratio; 100 parts resin to 50 parts curing agent. The use of a weighing scale is recommended over volumetric measuring. Any off-ratio excess of either the resin or curing agent can cause poor cure results and cause excessive chemical leaching that can transfer to the food or beverage. The substrate must be suitable and prepared for the intended purpose of the application. Remove any contaminants that may interfere with the complete cure of the MAX CLR resin system. Exclude the use of materials and components not suitable for food contact (lead-based pigments, harsh cleaners, and unsanitary conditions).PROPER CURING FOR DIRECT FOOD CONTACT Allow the applied resin to fully cure for a minimum of 48 hours at 75°F before exposing the coating to any foodstuffs. A short heat post cure at 150°F for 60 to 90 minutes will ensure the resin is fully cured. Rinse the cured coating with warm water and mild detergent before allowing any food contact. PRACTICAL GUIDE ON HOW TO USE THIS RESIN SYSTEM Review all published data regarding this product. Proper usage data and other detailed information are posted on this page. Mix the resin and curing agent only after the surface is prepared for application.STEP 1. SURFACE PREPARATION The quality of adhesion of any coating or adhesive application is dependent on how well the surface is prepared. The resin system must be able to properly 'wet-out' the surface to form a continuous film. Surfaces demonstrating poor wettability prevents the liquid resin from forming a cohesive bond. Improper surface wetting yields poor adhesion and will delaminate during use.Wetting is the ability of a liquid to interfaces or wet-out a solid surface; its dynamics is expressed as surface tension. A surface that demonstrates low surface tension, such as waxed surface, oily surface or slick plastics like Teflon will prevent the liquid resin to wet-out and cause poor adhesion. In the same respect, if the surface is coated from a previous application, the epoxy adhesion is limited to adhesion quality of the primary coating is applied over. Make sure to remove any loose or peeling old coating before application to avoid delamination. If possible remove the old coating by mechanical sanding or power washing so the applied epoxy is in direct contact with the base substrate. Applying a coating over oil-based stain should be avoided.Poor Wetting Of The Applied Resin (Crawling) Due To Oil-based Stain Applied On WoodWatch this video demonstrating how to check the surface before applying the MAX CLR as a coating or adhesive.The same coating retraction or crawling may occur when applying the MAX CLR on painted surfaces.Acrylic, latex, and other paints and spray paints contain silicone additives called surfacetants that produces a surface that demonstrates poor wetting and adhesion.The adhesion of the MAX CLR will only be as strong as the adhesion of the coating in direct contact with the substrate.It is highly recomended that the MAX CLR be applied directly to the base substrate as it yields higher adhesion quality than coatings or paints the MAX CLR resin system. Why Coatings Bead Up \u0026 Separate. Surface Test \u0026 Prep Before Applying Epoxy Coating To Avoid Crawling Video will open in a new window Using the eBay App? Paste link into a browser window: [isdntekvideo] Dome Coating With MAX CLR A/B Epoxy Dome Coating Application With MAX CLR A/BMAX CLR A/B HOT WATER IMMERSION TESTVideo will open in a new window MAX CLR A/B AVAILABLE KIT SIZES24 OUNCE KIThttps://www.ebay.com/itm/22262396319448 OUNCE KIThttps://www.ebay.com/itm/31194732010196 OUNCE KIThttps://www.ebay.com/itm/22262532906896 OUNCE KIThttps://www.ebay.com/itm/2226253382301.5 GALLON KIThttps://www.ebay.com/itm/222626972426 *********************************************************************************************** GUIDELINES COMPOSITE FABRICATIONBy simple definition, a composite material is a manufactured collection of two or more ingredients skillfully combined to form a new material that is defined by its performance that should uniquely greater than the sum of its individual parts. This method is also defined as a SYNERGISTIC COMPOSITION. Note The Uniformity Between The Impregnating Resin And Fiberglass Fabric Producing A Transparent Laminate (No Air Voids Or Porosity) Step One:Fabric SelectionTypes Of Fabric Weave Style And Fabric Finishing For Resin Type CompatibilityFabrics are generally considered ”balanced” if the breaking strength is within 15% warp to fill and are best in bias applications on lightweight structures. “Unbalanced” fabrics are excellent when a greater load is required one direction and a lesser load in the perpendicular direction. Common Weaves TypesPLAIN WEAVEIs a very simple weave pattern and the most common style. The warp and fill yarns are interlaced over and under each other in alternating fashion. Plain weave provides good stability, porosity and the least yarn slippage for a given yarn count. 8 HARNESS SATIN WEAVEThe eight-harness satin is similar to the four-harness satin except that one filling yarn floats over seven warp yarns and under one.This is a very pliable weave and is used for forming over curved surfaces.4 HARNESS SATIN WEAVEThe four-harness satin weave is more pliable than the plain weave and is easier to conform to curved surfaces typical in reinforced plastics. In this weave pattern, there is a three by one interfacing where a filling yarn floats over three warp yarns and under one.2x2 TWILL WEAVETwill weave is more pliable than the plain weave and has better drivability while maintaining more fabric stability than a four or eight harness satin weave. The weave pattern is characterized by a diagonal rib created by one warp yarn floating over at least two filling yarns. AVAILABLE FABRICS LENGTH CLICK THE LINK TO VIEW & ADD TO CART 1.5-Oz Fiberglass Plain Weave Style 120 5 Yards https://www.ebay.com/itm/222623985867 1.5-Oz Fiberglass Plain Weave Style 120 10 Yards https://www.ebay.com/itm/311946399588 7-Oz Fiberglass Plain Weave Style 7532 5 Yards https://www.ebay.com/itm/222624899999 10-Oz Fiberglass Plain Weave Style 7500 3 Yards https://www.ebay.com/itm/223496626702 10-Oz Fiberglass Plain Weave Style 7500 5 Yards https://www.ebay.com/itm/223495621157 10-Oz Fiberglass Plain Weave Style 7500 10 Yards https://www.ebay.com/itm/312585593625 9-Oz Fiberglass 8 Harness Satin Weave Style 7781 2 Yards https://www.ebay.com/itm/223669319695 9-Oz Fiberglass 8 Harness Satin Weave Style 7781 5 Yards https://www.ebay.com/itm/223508087559 9-Oz Fiberglass 8 Harness Satin Weave Style 7781 10 Yards https://www.ebay.com/itm/313471251199 26-Oz Fiberglass 8 Harness Satin Weave Style 1584 3 Yards https://www.ebay.com/itm/311947365010 5-Oz Kevlar 49 Fabric 8 Harness Satin Style 351 3 Yards https://www.ebay.com/itm/222623951106 6-Oz Carbon Fiber 3K Plain Weave With Tracers 3 Yards https://www.ebay.com/itm/311947292012 Fabric Nomenclature & SpecificationsThread Count: The number of threads (tow in carbon and yarn in Aramid) per inch.The first number will be the warp count and the second will be the fill count. Fill: The threads that run the width of the roll or bolt and perpendicular to the warp threads. Warp: The threads that run the length of the roll or bolt and perpendicular to the fill threads.Thickness: Measured in fractions of an inch. The thicker the fabric the more resin required to fill the weave to obtain a surface-smooth finished part.Finishing & TreatmentFabrics made from glass filament used for composites are chemical treatment to make it compatible with resin systems, therefore improving the bond between the fiber and the resin.Finishing fiberglass typically decreases the fiber strength by as much as 50%. Both Silane and Volan finishes are epoxy compatible. SATIN WEAVE TYPE CONFORMITY ONTO CURVED SHAPES Plain Weaves, Bi-axial, Unidirectional Styles For Directional High Strength Parts Use this weave style cloth when high strength parts are desired.It is ideal for reinforcement, mold making, aircraft and auto parts tooling, marine, and other composite lightweight applications.7544 Fiberglass - YouTubeStep Two: Choose The Best Epoxy Resin System For The ApplicationThe epoxy resin used in fabricating a laminate will dictate how the FRP will perform when load or pressure is implied on the part. To choose the proper resin system, consider the following factors that is crucial to a laminate's performance. Size And Configuration Of The Part(Number Of Plies And Contoured, Flat Or Profiled)Consolidating Force(Free Standing Dry Or Hand Lay-up, Vacuum Bag Or Platen Press Curing)Curing Capabilities(Heat Cured Or Room Temperature Cured)Mechanical Load Parameters(Shearing Force, Torsional And Directional Load, Beam Strength) Environmental ExposureThe Principal Role Of The Resin Is To Bind The Fabric Into A Homogeneous Rigid Substrate(Operating Temperature, Ambient Conditions, Chemical Exposure, Cyclic Force Loading)Material And Production Cost(Buying In Bulk Will Always Provide The Best Overall Costs)These factors will dictate the design and the composition of the part and must be carefully considered during the design and engineering phase of the fabrication. Top Selling Impregnating Resin System MAX BOND LOW VISCOSITY A/B Marine Grade Boat Building Resin System, Fiberglassing/Impregnating, Structural Strength MAX BOND LOW VISCOSITY 32-Ouncehttps://www.ebay.com/itm/311947109148MAX BOND LOW VISCOSITY 64-Ouncehttps://www.ebay.com/itm/311947125422MAX BOND LOW VISCOSITY 1-Gallon https://www.ebay.com/itm/311947117608MAX BOND LOW VISCOSITY 2-Gallon https://www.ebay.com/itm/311946370391MAX BOND LOW VISCOSITY 10-Gallonhttps://www.ebay.com/itm/222624960548 MAX 1618 A/B Crystal Clear, High Strength, Lowest Viscosity, Durability & Toughness, Excellent Woodworking ResinMAX 1618 A/B 48-Ounce Kithttps://www.ebay.com/itm/222627258390MAX 1618 A/B 3/4-Gallon Kithttps://www.ebay.com/itm/222625113128MAX 1618 A/B 3/4-Gallon Kithttps://www.ebay.com/itm/222627258390MAX 1618 A/B 1.5-Gallon Kithttps://www.ebay.com/itm/311946441558 MAX CLR A/B Water Clear Transparency, Chemical Resistance, High Impact Resistance, Low ViscosityMAX CLR A/B 24-Ounce Kithttps://www.ebay.com/itm/222623963194MAX CLR A/B 48-Ounce Kithttps://www.ebay.com/itm/311947320101MAX CLR A/B 96-Ounce Kithttps://www.ebay.com/itm/222625329068MAX CLR A/B 96-Ounce Kithttps://www.ebay.com/itm/222625338230MAX CLR A/B 1.5-Gallon Kithttps://www.ebay.com/itm/222626972426MAX GRE A/B Gasoline Resistant Epoxy Resin Resistant To Gasoline/E85 Blend, Acids & Bases, Sealing, Coating, Impregnating ResinMAX GRE A/B 48-Ounce Kithttps://www.ebay.com/itm/311946473553MAX GRE A/B 96-Ounce Kithttps://www.ebay.com/itm/311947247402 MAX HTE A/B High-temperature Epoxy Heat Cured Resin System For Temperature Resistant Bonding, Electronic Potting, Coating, BondingMAX HTE A/B 80-Ounce Kithttps://www.ebay.com/itm/222624247814MAX HTE A/B 40-Ounce Kithttps://www.ebay.com/itm/222624236832 Step Three:Proper Lay-Up Technique -Putting It All TogetherPre-lay-up notesLay out the fabric and pre-cut to size and set asideAvoid distorting the weave pattern as much as possibleFor fiberglass molding, ensure the mold is clean and adequate mold release is usedView our video presentation above "MAX EPOXY RESIN MIXING TECHNIQUE"Mix the resin only when all needed materials and implements needed are ready and within reachMix the proper amount of resin needed and be accurate proportioning the resin and curing agent. Adding more curing agent than the recommended mix ratio will not promote a faster cure. Over saturation or starving the fiberglass or any composite fabric will yield poor mechanical performance. When mechanical load or pressure is applied to the composite laminate, the physical strength of the fabric should bear the stress and not the resin. If the laminate is over saturated with the resin it will most likely to fracture or shatter instead of rebounding and resist damage.Don’t how much resin to use to go with the fiberglass?A good rule of thumb is to maintain a minimum of 30 to 35% resin content by weight. This is the optimum ratio used in high-performance prepreg (or pre-impregnated fabrics) typically used in aerospace and high-performance structural application. For general hand lay-ups, calculate using 60% fabric weight to 40% resin weight as a safety factor. This will ensure that the fabricated laminate will be below 40% resin content depending on the waste factor accrued during fabrication.Place the entire pre-cut fiberglass to be used on a digital scale to determine the fabric to resin weight ratio. Measuring by weight will ensure accurate composite fabrication and repeatability, rather than using OSY (ounces per square yard) or GSM ( grams per meter square) data.THE USE OF A WEIGHING SCALE IS HIGHLY RECOMMENDED Purchase this scale with any of our product offering and the shipping cost of the scale is free. https://www.ebay.com/itm/222630300203A good rule of thumb is to maintain a minimum of 30 to 35% resin content by weight. This is the optimum ratio used in high-performance prepreg (or pre-impregnated fabrics) typically used in aerospace and high-performance structural application. For general hand lay-ups, calculate using 60% fabric weight to 40% resin weight as a safety factor. This will ensure that the fabricated laminate will be below 40% resin content depending on the waste factor accrued during fabrication.Place the entire pre-cut fiberglass to be used on a digital scale to determine the fabric to resin weight ratio. Measuring by weight will ensure accurate composite fabrication and repeatability, rather than using OSY data.Typical fabric weight regardless of weave pattern 1 ounce per square yard is equal to 28.35 grams 1 square yard equals to 1296 square inches (36 inches x 36 inches)FOR EXAMPLE1 yard of 8-ounces per square yard (OSY) fabric weighs 226 grams 1 yard of 10-ounces per square yard (OSY) fabric weighs 283 gramsOunces per square yard or OSY is also known as aerial weight, which is the most common unit of measurement for composite fabrics. To determine how much resin is needed to adequately impregnate the fiberglass, use the following equation:(Total Weight of Fabric divided by 60%)X( 40%)= weight of mixed resin neededfw= fabric weigh rc= target resin content rn=resin needed MASTER EQUATION (fw/60%)x(40%)=rnFOR EXAMPLE1 Square Yard Of 8-ounce Per Square Yard (OSY) Fiberglass Fabric Weighs 226 Grams OSY Is The Common Term For The Fabric Density In The Composites Industry. (226 grams of dry fiberglass / 60%) X 40% = 150.66 grams of resin neededSo for every square yard of 8-ounce fabric, it will need 150.66 grams of mixed resin.Computing For Resin And Curing Agent Amount Needed For 150.66 Grams Of Mixed ResinMIX RATIO OF RESIN SYSTEM IS 2:1 OR 50 PHR (per hundred resin)2 = 66.67% (2/3) + 1 = 33.33%(1/3) (2+1)=3 or (66.67%+33.33%)=100% or (2/3+1/3)= 3/3 150.66 x 66.67%= 100.45 grams of Part A RESIN 150.66 x 33.33%= 50.21 grams of Part B CURING AGENT 100.45 + 50.21 = 150.66 A/B Resin MixtureGENERAL LAY-UP PROCEDURE Apply the mixed resin onto the surface and then lay the fabric over the applied resin. Allow the resin to saturate through the fabric.NOT THE OTHER WAY AROUNDThis is one of the most common processing error that yields sub-standard laminates. By laying the fiberglass onto a layer of the prepared resin, less air bubbles are entrapped during the wetting-out stage. Air is pushed up and outwards instead of forcing the resin through the fabric which will entrap air bubbles. This technique will displace air pockets unhindered and uniformly disperse the impregnating resin throughout the fiberglass.HAND LAY-UP TECHNIQUE Minimize air entrapment or voids during the epoxy/fiberglass lay-up process to maximize the best strength performance. Air voids or porosity in a composite fiberglass structure is where failure originates when force is applied.Fiberglass Hand Lay Up For Canoe and Kayak BuildingVideo will open in a new windowBasic Hand Lay-up FiberglassingVideo will open in a new windowVACUUM BAGGING PROCESS For performance critical application used in aerospace vehicles, composite framing for automotive vehicles and marine vessels, a process called 'Vacuum Bagging' is employed to ensure the complete consolidation of every layer of fabric. The entire tooling and lay-up are encased in an airtight envelope or bagging and a high-efficiency vacuum pump is used to draw out the air within the vacuum bag to create a negative atmospheric pressure. Once a full vacuum (29.9 Inches of Mercury) is achieved, the negative pressure applies a compacting force of 14.4 pounds per square inch (maximum vacuum pressure at sea level) is applied to the vacuum bag transferring the force to the entire surface area of the laminate. Vacuum pressure is maintained until the resin cures to a solid. For room temperature curing resin system, the vacuum pump is left in operation for a minimum of 18 hours. External heat can be applied to the entire lay-up, thus accelerating the cure of the resin system. The vacuum force also removes any entrapped air bubble between the layers of fabric and eliminate what is called, porosity or air voids. Porosity within a laminate creates weak spots in the structure that can be the source of mechanical failure when force or load is applied to the laminate. The standard atmosphere (symbol: atm) is a unit of pressure defined as 101325 Pa (1.01325 bar), equivalent to 760 mm Mercury or 29.92 inches Mercury or14.696 pounds per square inch of pressure. Vacuum BaggingVideo will open in a new windowAUTOCLAVE CURING PROCESS Autoclave curing processing is the most common method used in the large-scale production of composite products. The Aerospace Industry, which includes space exploration rockets and vehicles, deep space structures, and commercial and military airplane utilizes this composite fabrication process due to the critical nature of the application. The mechanical demands of the composite are often pushed to the upper limits and autoclaved process yields composites with the best weight to strength ratio. BASIC OPERATION OF THE AUTOCLAVE PROCESSIn the autoclave process, high pressure and heat are applied to the part through the autoclave atmosphere, with a vacuum bag used to apply additional pressure and protect the laminate from the autoclave gases. The cure cycle for a specific application is usually determined empirically and, as a result, several cure cycles may be developed for a single material system, to account for differences in laminate thickness or to optimize particular properties in the cured part.The typical autoclave cure cycle is a two-step process. First, vacuum and pressure are applied while the temperature is ramped up to an intermediate level and held there for a short period of time. The heat reduces the resin viscosity, allowing it to flow and making it easier for trapped air and volatiles to escape. The resin also begins wetting the fibers at this stage.In the second ramp up, the temperature is raised to the final cure temperature and held for a sufficient length of time to complete the cure reaction. During this step, the viscosity continues to drop, but preset temperature ramp rates and hold times then stabilize viscosity at a level that permits adequate consolidation and fiber wetting, while avoiding excessive flow and subsequent resin starvation. These control factors also slow the reaction rate, which prevents excessive heat generation from the exothermic polymerization process. Upon completion, the cured mechanical performance of the composite is often much stronger and lighter compared to a hand lay-up, or vacuum bagged composite laminate. VACUUM INFUSION PROCESSVacuum Infusion Process is also known in the composites industry as Vacuum Assisted Resin Transfer Molding or VARTM.Similar to the Vacuum Bagging Process where the negative pressure is used to apply consolidation force to the laminate while the resin cures, the resin is infused into the fabric lay-up by sucking the impregnating resin and thus forming the composite laminate.The VARTM Process produces parts that require less secondary steps, such as trimming, polishing or grinding with excellent mechanical properties. However, the vacuum infusion requires more additional or supplemental related equipment and expendable materials. So the pros and cons of each presented composite fabrication process should be carefully determined to suit the user's capabilities and needs.Please view the following video demonstration of Vacuum Infusion or VARTM process.MAX 1618 A/B VACUUM ASSISTED RESIN TRANSFER MOLDING PROCESSCARBON FIBER VACUUM INFUSION WITH EPOXY RESIN - VACUUM BAGGING WITH MAX 1618 EPOXY RESIN - YouTubeVideo will open in a new windowStep Four: Proper CuringAlthough we have formulated all of our MAX EPOXY RESIN SYSTEM product line to be resistant to amine-blush, it is recommended not to mix any resin systems in high humidity conditions, greater than 70%. Make sure that the substrate or material the epoxy resin system is being applied to is well prepared as possible to ensure the best-cured performance. Review the published data and information for proper usage, application, and general safety information. Our expert staff of engineers is always available for consultation and assistance. Allow the lay-up to cure for a minimum of 24 to 36 hours before handling.Optimum cured properties can take up to 7 days depending on the ambient cure condition. The ideal temperature cure condition of most room temperature epoxy resin is 22°C to 27°C at 20% relative humidity. Higher ambient curing temperatures will promote faster polymerization and development of cured mechanical properties. IMPROVING MECHANICAL PERFORMANCE VIA POST HEAT CURE A short heat post cure will further improve the mechanical performance of most epoxy resins. Allow the applied resin system to cure at room temperature until for 18 to 24 hours and if possible, expose heat cure it in an oven or other sources of radiant heat (220°F to 250°F) for 45 minute to an hour. You can also expose it to direct sunlight but place a dark colored cover, such as a tarp or cardboard to protect it from ultraviolet exposure. In general, room temperature cured epoxy resin has a maximum operating temperature of 160°F or lower.A short heat post cure will ensure that the mixed epoxy system is fully cured, especially for room temperature cure system that can take up to 7 days to achieve 100% cure.Some darkening or yellowing of the epoxy resin may occur if overexposed to high temperature (>125°C). AMINE BLUSHThe affinity of an amine compound (curing agent) to moisture and carbon dioxide creates a carbonate compound and forms what is called amine blush. Amine blush is a wax-like layer that forms as most epoxies cure. If the epoxy system is cured in extreme humidity (>70%).It will be seen as a white and waxy layer that must be removed by physical sanding of the surface followed by an acetone wipe. OTHER TYPES OF EPOXY RESIN CURE MECHANISMLATENT CURING SYSTEMSLatent epoxy resins are systems that are mixed together at room temperature and will begin polymerization but it will not achieve full cure unless it is exposed to a heat cure cycle. In general, these are high-performance systems that demonstrate exceptional performance under extreme conditions such as high mechanical performance under heat and cryogenic temperatures, chemical resistance or any environment that epoxy room temperature system perform marginally or poorly. Upon the mixing of the resin and curing agent polymerization will begin and will only achieve a partial cure. Some resins may appear cured or dry to the touch, this state is called 'B-Stage Cure', but upon application of force will either be gummy or brittle almost glass-like and will dissolve in most solvents. The semi-cured resin must be exposed to an elevated temperature for it to continue polymerization and achieve full cure. HEAT ACTIVATED CURING SYSTEMSThis type of epoxy system will not polymerize unless it is exposed to the activation temperature of the curing agent which can be as low as 100°C and as high as 250°C. TESTING THE COMPOSITE Determination Of The Fabric To Resin Ratio TESTING FABRIC TO RESIN RATIO VIA RESIN BURN OUTVideo will open in a new windowULTIMATE COMPRESSIVE STRENGTH ULTIMATE COMPRESSIVE STRENGTH TEST Video will open in a new window6500 Pounds / 0.498 square inch = 13,052 psi Maximum Compressive StrengthSPECIMEN EXAMINATION AFTER COMPRESSION TESTVideo will open in a new window**************************************************************** PLEASE CHECK OUT OTHER AVAILABLERESIN SYSTEMS AT OUR eBay STOREFor our complete listing, please Visit our eBay store! DON'T FORGET OUR EPOXY MIXING KITClick The Link To Add To Order https://www.ebay.com/itm/222623932456EVERYTHING YOU NEED TO MEASURE, MIX, DISPENSE OR APPLY Proportioning the correct amount is equally as important to attain the intended cured properties of the resin system. The container in which the epoxy and curing agent is mixed is an important consideration when mixing an epoxy resin system.It must withstand the tenacity of the chemical and must be free of contamination.Most epoxy curing agent has a degree of corrosivity, as a general practice, protective gloves should be worn when handling chemicals of the same nature. MIXING KIT CONTENTS 1 Each Digital Scale -Durable, Accurate Up To 2000.0 Grams 4 Each 32-ounce (1 Quart) Clear HDPE Plastic Mix Cups4 Each 16-ounce (1 Pint) Clear HDPE Plastic Mix Cups5 Pairs One Size Fits All Powder-Free Latex Gloves 2 Each Graduated Syringes8 Wooden Stir Sticks8 Assorted Size Foam Brush IMPORTANT NOTICEYour purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.The user should thoroughly test any proposed use of this product and independently conclude the satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval.The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.There is no warranty of merchantability for fitness of use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind. Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 33.3 USD
Location: Ontario, California
End Time: 2024-08-23T19:53:12.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: MAX EPOXY RESIN SYSTEMS
Warranty: 1 Year
FOR KNIFE SCALE FABRICATING: High Impact And Shatter Resistant
CRYSTAL CLEAR COLOR STABLE CASTING RESIN: Pen Blanks, Knife Scales, Dome Coating
HIGH GLOSS WOOD COATING SEALING BONDING: FDA Compliant For Direct Food Contact
KAYAK, CANOE, PADDLE BOARD, SURFBOARD: Will Not Harm Polystyrene Or EPS Foam
Manufacturer Part Number: MAX CLR A/B 24 Ounce Kit
IMPREGNATING RESIN COMPOSITE FABRICATING: Fiberglass, Carbon Fiber, Kevlar
Country/Region of Manufacture: United States
Modified Item: No
California Prop 65 Warning: PROP 65 WARNING: This product contains less than 0.1% of a chemical known to the State of California to cause cancer. EPA SARA Title III Section 313 above ‘de minimus’ level: None All components of this product are on the TSCA Inventory or are exempt per 40 CFR 720.30 IMPORTANT USAGE INFORMATION POSTED ON THE DESCRIPTION PAGE
