For 2003-2006 Toyota Camry 2.4L 234-4624 Oxygen O2 O2 Sensor Upstream Front

Description: Compatibility: please check the compatibility before you purchase. 1993-1997 Lexus GS300 3.0L2003-2006 Toyota Camry 2.4L2000-2002 Toyota Echo 1.5L2000-2005 Toyota MR2 Spyder 1.8L2001-2003 Toyota Prius 1.5L1998-2000 Toyota RAV4 2.0L1998-2000 Toyota RAV4 ELEC Feature: Corrosion-resistant stainless steel constructionIn easier installation and resistance to high temperatures, vibration damage and wire corrosion, which protects signal accuracy and longevity.Industrys fastest light-off times to reduce cold-start emissions and improved fuel economy over aging sensorUnique sensor coatings protect elements from premature failure and are validated for lifetime operation with E85 and other alcohol-based fuels. Oxygen Sensor Q & A 1. How many oxygen sensors are on todays engines?It depends on the model year and type of engine. On most four and straight six cylinder engines, there is usually a single oxygen sensor mounted in the exhaust manifold. On V6, V8 and V10 engines, there are usually two oxygen sensors, one in each exhaust manifold. This allows the computer to monitor the air/fuel mixture from each bank of cylinders.On later model vehicles with OBD II (some 1993 and 94 models, and all 1995 and newer models), one or two additional oxygen sensors are also mounted in or behind the catalytic converter to monitor converter efficiency. These are referred to as the downstream O2 sensors, and thee will be one for each converter if the engine has dual exhausts with separate converters. 2.Where is Oxygen Sensor Locations? When troubleshooting oxygen sensor problems with a scan tool, you may find a diagnostic trouble code for one of the O2 sensors. The code displayed on your scan tool will indicate the type of fault, and identify one of the oxygen sensors by its position in the exhaust system. The oxygen sensors location will be identified by position (sensor 1, sensor 2 or sensor 3), and by cylinder bank (bank 1 or bank 2).Most late model engines have multiple oxygen sensors, so which one is sensor 1, 2 or 3, and how do you know which cylinder bank is 1 or 2? On straight four and six cylinder engines, there is only one bank of cylinders. So all of the oxygen sensors will be bank 1. The oxygen sensor or Air/Fuel sensor closest to the engine in the exhaust manifold will always be Sensor 1. The O2 sensor located in or behind the catalytic converter will be Sensor 2. The location of the number one cylinder on import engines will vary depending on the year/make/model. One way to find number one cylinder so you can identify bank 1 is to look at the ignition system. If it has a distributorless ignition system (DIS) or a coil-on-plug (COP) ignition, the plug wires or coils may have lettering or marking indicating the cylinder numbers. If a V6, V8 or V10 engine has dual exhausts with dual converters, the downstream O2 sensors would be labeled Bank 1, Sensor 2 and Bank 2, Sensor 2. Or, the downstream oxygen sensor might be labeled Bank 1 Sensor 3 if the engine has two upstream oxygen sensors in the exhaust manifold (some do to more accurately monitor emissions). 3.how to replace an oxygen sensor Step 1. Locate the oxygen sensor on your vehicle by looking for a part that looks like a spark plug that sticks out from the exhaust pipe. It will have an electrical connection attached to it. Step 2. Disconnect the electrical connection on the oxygen sensor. Use a flat tip screwdriver to push in the tabs and pull the connection apart. Step 3. Unscrew the oxygen sensor off the exhaust pipe using either an open-end wrench or a special socket made to remove it. The majority of oxygen sensors will take an SAE 7⁄8 inch (2.2 cm) wrench. Step 4. Compare your new oxygen sensor to the old one. If the new one did not come with an electrical connection, but just with the wires stubbed out, you need to do a little work. ?Cut off the old connector from the bad oxygen sensor, strip the wires and solder the wires to the new oxygen sensor. You can also use butt connectors. ?Use heat sensitive shrink tape to seal the connections. ?Follow manufacturers instructions to know which wires to tie together. Step 5. Reverse the steps used in removing the oxygen sensor and install the new part. Add a small amount of anti-seize to the threads of the new sensor. Screw it in place clockwise and snug it down with the socket or open-end wrench. Do not over tighten the sensor as you might strip the threads. Step 6. Plug the electrical connections back in. Step 7. Turn on the ignition key, but do not start your vehicle. Use the diagnostic scanner/reader to clear the code from the vehicles computer. Step 8. Start the car. You should notice an immediate improvement. Contact us: Please contact us if you have any question. Payment 1.We accept Multiple Payment Methods, such as PayPal, VISA, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 10 days as auction ended or order might be delayed. Shipping 1. Orders processed within 24 hours of payment verification.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address. 3. The images shown are not the actual item and are for your reference only. 4. Fast shipping:All our packages use USPS First Class Package Service 5. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! Returns 1. You have 7 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. Warranty 1. 12 months Manufacturers Warranty for defective items (excluding items damaged and/or misused after receipt). Accessories come with a 3-month warranty. 2. Defective items must be reported and returned to us within the warranty period (and in the original packaging, if possible). You must tell us what the defect is and give us your eBay ID. we do not repair or replace items with an expired warranty. You agree to all of the above-listed policies upon bidding on and winning this auction! Feedback 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! Majorin-AutoParts_All rights reserved.

Price: 14.99 USD

Location: Ontario, California

End Time: 2025-01-03T20:38:16.000Z

Shipping Cost: 0 USD