Geiger counter dosimeter 3.3V kit /w bat. charger Arduino IDE compat. assembled

Description: important note: As of mid September 2017 eBay started enforcing its policy to restrict linking to proprietary and social media sites inside listings like this one.Subsequently it became more difficult to present different aspects of the product directly in the listing. Therefore please feel free to ask by messaging me if you have questions.---You are bidding for the new - Native 3.3V revision , fully assembled, microprocessor-based ionising radiation counter with 3.3V Black-on-Green LCD and included Li-Po/Li-Ion charger breakout board.!note: for safety reasons it is important to use LiPo/LiIon batteries which have integrated protections (most Li-Po usually have but check if yours have). if you are unsure, or know for sure, that your battery is not protected (most 18650 Li-Ion often are not protected), please message me and ask for the charger with the integrated protection circuit so I include the right one for your battery.This means, device can be directly (without any converters) powered by almost any 3.7-4.2V rechargeable battery. (above demo videos are for reference only - items depicted are not a part of this listing)---While retaining all the previous features and functions of the previous designs,- new version is more compact and is mainly based on SMD components;- has a tone mode for search of the radioactive source (like in a metal detector) switchable On or Off with an installed microswitch;- LCD backlight is now switchable On or Off by double-clicking the "MODE" button;- sound is now also switchable On or Off by double-clicking the "TONE-ZEROING" button;- switching between the "Primary" and "Secondary" conversion rates is now done by long-pressing the "TONE-ZEROING" button with an few seconds indication of which rate is chosen on the LCD;- additional potentiometer is installed to reduce the brightness of the LCD backlight (which provides essential battery power savings);- High Voltage is now adjustable from < 100 to >800V which allows reliable use of most popular Geiger-Müller tubes;- JTAG, i2C, TTL level Serial and battery power headers are provided for extension and connectivity purposes---This listing is without the Geiger–Müller tube, TTLSerial<>USB adapter and battery. In order to use it you need to have a Geiger–Müller tube which has it's working voltage in the interval from 100 to 800V. Currently I also have the following tubes in stock (please inquire by message if you need any): SBT-9 (alpha beta and gamma)SI-29BG (beta and gamma)SBM-20 (beta and gamma)CTC- 5 (beta and gamma)SBT11 (alpha beta and gamma)SBT11A (alpha beta and gamma)SI8B (alpha beta and gamma)SBT10 (alpha beta and gamma)SBT10A (alpha beta and gamma)SBM-20 (beta and gamma)SBM-21 (beta and gamma)SI22G (gamma)SBT-9 (alpha beta and gamma)SI-29BG (beta and gamma)SI19BG (alpha beta and gamma)SI8B (alpha beta and gamma) This device is preloaded with a newly feature - amended geiger kit sketch (v.11.0.2 3.3V) sketch is a free software and is available through my blog (can't give a link here because as of September 2017 eBay started to prevent linking to proprietary sites, but you can search arduino-geiger-pcb with your favorite serarch engine and find it in my blog on blogspot).The schematics of the device is also available but as links can no longer be given here try to look for impexeris on GitHub. (please read more about features of v.11.0.2 3.3V below on this page) This device has an integrated IR receiver and a menu system controllable with any NEC (preset as default), or Sony type IR TV remote. (note: IR TV remote is not a part of the listing)Besides control of multiple other parameters this feature allows changing CPM>uSv or uR ratio for tubes through the menu without a need to reprogram the firmware. IR remote control pictured below is not a part of this listing but is available as an option for additional 4 USDIf you would like one included please ask before paying and I shall adjust the e-bay invoice. If your Android phone has a iR transmitter you can use the free app from the Google play store:It is called Universal TV Remote from developer called Twinone When you install this app then download the custom remote file with your phones Internet browser: (can't give a link here because as of September 2017 eBay started to prevent linking to proprietary sites, but you can search arduino-geiger-pcb with your favourite search engine and find it in my blog on blogspot) and open it (when asked which app to use for opening it choose the app you you have just installed) note: the above custom remote file is when firmware which is configured to work with Sony system remotes uploaded (this is the default configuration of firmware for boards in this listing) note: You can choose either Black-on-Green (default) or White-on-Blue LCD display. a limited number of Black-on-Green with Black-on-Orange when backlit displays are available for extra 8.8 USD. Please contact me by a message if you want a display other than Black-on-Green Some videos (for reference only - not a part of this listing) --- Schematics takes its origins from a Geiger counter schematics publicly available on the Internet - on DIYGeigerCounter page and is further advanced with the final schematics freely available (as by eBay policies enforced on September 2017, proprietary links can no longer be given in listings, try to look for impexeris on GitHub) This device is preloaded with adapted GeigerKit sketch (v.11.0.2 3.3V). Sketch is a free software and is available (can't give a link here because as of September 2017 eBay started to prevent linking to proprietary sites, but you can search with your favourite search engine for arduino-geiger-pcb and find it in my blog on blogspot). DESCRITPIONCounter: can detect α, β and γ ionizing radiation depending on the Geiger–Müller tube you shall connect. simultaneously displays the Count Per Minute (CPM) and equivalent dose rate of radiation in μSv/h on the LCD display. indicates detection of ionizing particles with clicking sound and flashes of the yellow LED. (has a jumper for disconnecting-muting the buzzer); has a TTL-serial connector for connection to a computer (more information on connection to computer - below);when connected to computer counter outputs CPM, μSv/h and power voltage data in one minute intervals; a threshold LED lights up when preprogrammed threshold in Counts Per Minute (CPM) are exceeded. Push-button is provided for initial threshold value setup and change of the display modes (screens) - please reed more about that below in the Software functionality description section. Use of other tubes This counter circuit is well suited for use with any other Geiger–Müller tubes wether produced for just γ just 𝜶 or combined β+γ or universal 𝜶+β+γ detection. When using other tubes it is important that:- tube is specified to reliably operate in the voltage interval up to 800V.- specified tube anode resistor value is around 5,3 MΩ (note: some other - usually energy compensated 𝜶+β+γ tubes could require a different anode resistor value but changing this resistor is easy - please ask) note: a) voltage can be adjusted by trimmer potentiometer present on the PCB. b) the CPM to μSv/h ration for that particular tube can be changed by IR Sony type TV remote LCD display LCD display is a 2 Line x 16 character backlit display. You can choose either Black-on-Green (default) or White-on-Blue LCD display. Please contact me by message is you prefer White-on-Blue LCD installed. Powering the Geiger Counter is designed to be powered from rechargeable 3.7V/ 4.2V LiPo or LiIon batteries and. However it can also be powered from a 9V battery (it is recommended to buy a quality 6LR61 type battery in this case) .The device has a step-down regulator which provides the native 3.3V for the whole schematics. !note: It is important to connect the power in correct polarity in order to prevent burning that regulator! When connected to computer (TTLSerial<>USB converter which is not a part of this listing is needed), counter can be powered throughout the TTL-Serial header and draw power from the computer.!note: when powering through the USB adapter, the 3.3V pin should be used for the VCC! Power consumption With the LCD backlight being Off device draws 15 mA from battery. With LCD backlight fully ON total current drawn is around 44mA however with the 10K LCD brightness trimmer power draw can be reduced up to 18mA. When using Tone mode, power draw can peak to 75 - 100 mA. Connecting to a computer Circuit has a TTL-serial connector (the 90 degree bent header) this is a serial connector, however it operates at Transistor to Transistor Voltage levels and can be connected to the computer through appropriate ttl-com port or ttl-usb adapter (TTLSerial<>USB converter which is not a part of this listing is needed). When connected to computer Counter can be a) powered from the computer b) simultaneously outputs to the standard serial terminal CPM, μSv/h and power voltage data in one minute intervals. Software The Software for the Counter is open-source (please ask if you need/want it in the file), developed in Arduino.cc Integrated Development Environment (IDE), which is very easy to grasp even for non-pros compared to programming in C. Therefore this counter is also good opportunity to learn about micro-controllers and change the software to your taste. Version v.11.0.2 3.3V features: Alarm threshold settable at power-on (retained in eeprom). Eeprom can be reset to default values by holding the "Mode" button during boot.Alternate display (by press of the button)A "quick response" bar graph (search aid)Tone mode (radioactive source search aid) Alarm (optional): When the CPM exceeds a preset value, the red threshold LED shall be lit.When the CPM drops back under the initially preset alarm threshold the LED whale go off. The alarm threshold is configured during power up. After the first few screens you will see a "Set Alarm" prompt. To preset the alarm you have to use a push button or simply let the preset function time out (in 3 sec. of inactivity) to keep the then current setting. Pushing the button point shall start a list of alarm settings. Push the button (or hold it down) until you find the desired setting, then release the button to set that last value. After the 600 CPM setting, the choices repeat. The possible settings increment by 10 until 100 CPM and then by 50 until the 600 CPM setting. There is also a "No Alarm" setting. The chosen setting is retained in eeprom so it does not need to be set each time. Second Screen: The same push button used to set the alarm is used to turn on or off the second screen. The chosen screen stays on until the button is pushed again. The first time the screen is entered, the totals will begin to accumulate from zero. After accumulation has started, reentering the mode will display the totals that have accumulated. The second screen shows values for 1 minute and 10 minute periods. While the period is in progress (time not reached) the accumulated counts for the period are displayed. (On the 10 minute line, the elapsed time is also shown on the right side.) When a given period is complete, the format of the display changes . It then becomes the running average of CPM and uSv/h for the last 1 minute and 10 minute periods. The second screen is updated every 5 seconds. Bar Graph: The bar graph on the first screen shows quick changes in counts to make it easier to spot trends when surveying. It has a sample rate of 1/20 of a second. by default Output is configured for Radiation logger software. Please see the adaptation notes on my blog (can't give a link here because as of September 2017 eBay started to prevent linking to proprietary sites, but you can search arduino-geiger-pcb. Then on the blog look for the article called "How to prepare using Radiation logger").note: TTLSerial<>USB converter which is not a part of this listing is needed. Convenience features:- LCD backlight is now switchable On or Off by double-clicking the "MODE" button;- sound is now also switchable On or Off by double-clicking the "TONE-ZEROING" button;- switching between the "Primary" and "Secondary" conversion rates is now done by long-pressing the "TONE-ZEROING" button with an few seconds indication of which rate is chosen on the LCD;- additional potentiometer is installed to reduce the brightness of the LCD backlight (which provides essential battery power savings);- v.11.0.2 3.3V has a low battery indiction when the after-regulator voltage decreases to 3299mV Other: This adapted firmware version contains multiple other features present in original v.11.0.1 Please refer to the DIYGeigerCounter site for details. ---if you have a 3D printer you can print yourself an enclosure for the electronics of this kit it is on thingiverse (thing numbers are 1934646 for use with SBM-20/STS-5 tubes, 2502772 for use with SBT9 and 1934646 for use with si29bg tube) these above pictures are for reference only (not part of this listing)(if you need one pease check this listing) --- Dimensions PCB 42.5mm(1.673in) x 92.9mm(3.658in) x 21.7mm(0.854in)LCD 35.6mm(1.4in) x 78.7mm(3.1in) x 10.2mm(0.4in) --- I shall accept paypal only and shall attempt sending the board within one working day after the receipt of the payment. You shall have to bear any customs or other duties and taxes of your country whatsoever. I shall ship the item from Europe Worldwide as a Standard Int`l package. Please allow enough time for a shipment to arrive especially if item is sent between continents. I usually receive packages from Europe within 1-1,5 weeks and from USA or Asia 2 to 3 weeks. Happy bidding! Please check other items I am selling on eBayThank you for reading!

Price: 37.05 USD

Location: Vilnius

End Time: 2024-03-04T01:54:55.000Z

Shipping Cost: 14 USD