Ground Grid Regulated Power Supply( ±200VDC) DIY KIT & Finished Board

Description: Ground Grid Regulated Power Supply( ±200VDC) DIY KIT & Finished Board DIY KIT ProjectTo complete this project, high level knowledge of electronics and rich experience in terms of soldering and testing are required.Due to time zone and language communication restrictions, we can only provide limited technical support, and you need to solve problems by yourself. We do not provide information other than the product introduction page.MOFI-Ground Grid Regulated Power Supply( ±200VDC) DIY KIThigh-voltage:The high-voltage power supply uses MOSFET as pass transistors, which have a sense of tube sound characteristics but rejecting the rectification and regulation noise.high-voltage soft-start feature is included which will take about 5 second to reach the designed voltage protecting the tube from any voltage shock.low-pass filter prevents power noise from being introduced into the amplifier. Provide purer power supply .Onboard heatsinks used which would allow the 2SK2700 to supply up to 0.1A continuousMore sustained currents are possible by using larger, offboard heatsinks.(2A)heater –voltage:heater -voltage soft-start feature for vacuum heater is included which will take about 5 second to reach the designed voltage(6.3v or 12.6v) protecting the tube from any voltage shock and extending life.Onboard heatsinks used which would allow the LT1085CT to supply up to 1A continuousMore sustained currents are possible by using larger, offboard heatsinks.(2A)PCB comes with component parameters for easy installationDo not short the output terminal to discharge capacitor, otherwise it will damage the power board.Product configurationDIY kit: Contains the PCB and the components needed on the PCB, but does not include the power transformer.Finished board: Based on the well-tested board on the standard version kit, we verified all key points' voltage, and used the signal generator and oscilloscope for analog waveform double verification. We will not use this board for listening test.All finished pcbs are all carefully hand-soldered and fully tests, so the price is higher and less cost performance. Price-sensitive consumers but with have DIY ability are recommended to choose the kit.DIY KIT InstructionsSince the PCB holes are plated through, you only need to solder the parts from the bottom of the board. Do not drill or enlarge the holes because that would damage the through-plating.Clean both sides of the blank PCB with paper towel and isopropyl alcohol or electronics flux remover, then solder the components to the board, starting with the lowest profile parts. This means the resistors and zener diode. Then solder the small capacitors, small transistors, followed by the larger capacitors.Make sure the correct part goes into each position on the circuit board. Measure each resistor with your multimeter to ensure it's the proper value.Pay attention to the polarity of electrolytic capacitors, diodes, , transistors as well as the orientation.Clean up the solder flux residue from the board with isopropyl alcohol (or electronics flux remover) and a brush.Inspect all solder connections carefully, using a magnifying glass, to make sure there are no solder bridges or cold solder joints. Use a multimeter in ohms scale to check for short circuits.Parts list Payment Method: PayPal preferred Shippment:1. Shipping to international by China Post Airmail, every parcel will be registered with tracking number. We can also ship by FedEx/TNT/EMS for alternative shipping method for corresponding fees. Please let us know before payment if you need split shipment. 2.International shipping requires complicated shipping procedures (such as both countries customs, transit stations etc.), also will be affected by many factors, such as holidays, weather conditions etc, If you have not received your shipment within 30 days from payment, please contact us. Returns & Replacements & Repair:We accept returns & replacements within 30 days from the day the customer receive the products, please make first contact within 30 days from receiving the order. Products should be returned in original condition. As a benefit to our customers, we also provide repair within 3 months from the day when this item is shipped out, after repair is done, we will send you the item, but the customer should pay both shipping ways. Feedback:1)Your Feedback is really important to us, please take a few seconds to leave great feedback if you are satisfied with our product or service, thanks!2)We always offer the lowest price for best goods and service to you.3) Please contact us before leaving neutral(3 stars) or negative(1-2 stars) feedback.We will try our best to solve the problem and make you satisfied.

Price: 23.39 USD

Location: wuhan

End Time: 2025-01-10T07:01:59.000Z

Shipping Cost: 4 USD