Description: Obtaining adequate bond strength when bonding plastic-to-plastic substrates or plastic to dissimilar substrates is often a challenge for bonding. In general plastic surfaces demonstrates poor ‘wettability’ or the ability of a liquid to form a continuous film. These types of substrates or are called LSE or Low Surface Energy substrates and in general, most thermoplastic surfaces fall into this category. Teflon or its generic name PTFE and other polyethylene derivatives such as HDPE, LDPE, UHMW and olefinic-based plastics demonstrate poor liquid wettability due to its low surface energy. To create a viable bondable surface condition for these types of plastics, it must be surface treated by creating a superficial oxidized surface to increase its dynamic surface tension. Various types of physical treatment can be used to increase the surface energy of plastics, mostly through oxidation of the superficial layer. Flame treatment is the most widely used and cost-effective pre-treatment for polyethylene (HDPE, LDPE, UHMW) and polyolefin-based plastics prior to polymer bonding or printing. The resulting change of the surface by creating an oxidized layer onto the substrate greatly improves the ability of liquids wet-out the surface thus creating a strong adhesive bond between the surface and the coating. A Flame Treating process consists of exposing the surface to a suitable oxidizing flame for a period in the range 0.2 to 3.0 seconds. This treatment brings about a change to the polymer surface that increases its surface energy allowing fluids to effectively wet-out the surface and permits a strong adhesive molecular and mechanical bond. Flame Treating Using A Commercially Available Propane Torch Adjust the propane torch so that a low oxygen burning flame is achieved and pass over the area to be treated several times until a slight haze is noticed on the surface of the substrate. Using A Dyne Pen To View The Improve Surface Wetting Of the Untreated And Flame Treated UHMW plastic. Flame Treating the plastic substrate will make adhesion possible and create a strong bond.Flame Treated Surface Ideal For Bonding Joint Designs For Best Adhesion Performance Joint and Bonding And Design Suggestions Load Testing For Tensile Shear Strength of the Adhesion Types of stress load For Concrete Koi Pond Construction And Repair Stones And Decorative Boulders Were Bonded In Place WithMAX BOND THIXOTROPIC A/B Suitable For Continuous Under Water Applications Plywood Aquarium Construction With MAX BOND THIXOTROPIC A/B Adhesive Creates A Strong Waterproof Bond THANKS FOR STOPPING BY IMPORTANT NOTICE Your purchase constitutes the acceptance of this disclaimer. Please review before purchasing this product.The user should thoroughly test any proposed use of this product and independently conclude satisfactory performance in the application. Likewise, if the manner in which this product is used requires government approval or clearance, the user must obtain said approval. The information contained herein is based on data believed to be accurate at the time of publication. Data and parameters cited have been obtained through published information, PolymerProducts and Polymer Composites Inc. laboratories using materials under controlled conditions. Data of this type should not be used for a specification for fabrication and design. It is the user's responsibility to determine this Composites fitness for use.There is no warranty of merchantability of fitness for use, nor any other express implied warranty. The user's exclusive remedy and the manufacturer's liability are limited to the refund of the purchase price or replacement of the product within the agreed warranty period. PolymerProducts and its direct representative will not be liable for incidental or consequential damages of any kind.Determination of the suitability of any kind of information or product for the use contemplated by the user, the manner of that use and whether there is any infringement of patents is the sole liability of the user.
Price: 31.39 USD
Location: Ontario, California
End Time: 2024-09-03T19:21:52.000Z
Shipping Cost: 0.72 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Model: MAX BOND THIXOTROPIC A/B
Modified Item: No
Country/Region of Manufacture: United States
California Prop 65 Warning: US. California Safe Drinking Water & Toxic Enforcement Act (Proposition 65) This product does not contain any chemicals known to the State of California to cause cancer, birth defects, or any other harm. US. Toxic Substances Control Act All components of this product are on the TSCA Inventory or are exempt from TSCA Inventory requirements under 40 CFR 720.30 European Inventory of Existing Commercial Chemical Substances (EINECS) Components of this product are not listed on EINECS because they are polymers or "no-longer polymers" marketed before the enforcement of the 7th Amendment to Directive 67/548/EEC.
CONTROLLED VERTICAL FLOW: Use For Vertical Or Overhead Bonding
STRUCTURAL STRENGTH ADHESION: Permanent Bond To Metal, Glass, Marble, Wood
WATER, CHEMICAL RESISTANT BOND: Marine Grade For Both Salt And Fresh Water
FOOD SAFE ADHESIVE: Complies With FDA For Direct Food Contact Adhesive
HOBBIES, CRAFTS, SPORTING GOOD: High Impact Heat Resistant Extreme Cold Adhesive
Type: Epoxy Resin Glue
MPN: MAXTHIXO32OZ
Brand: MAX EPOXY RESIN SYSTEMS
