Description: Nubian Pyramid Connector KitFor use with Schedule 40 PVC pipe Offered is one 5 piece set of semi-flexible plastic connectors and apex for constructing a 72° angle Nubian pyramid. The slope angle of this style pyramid structure is much steeper than the 51° 51” Giza style pyramid and considered by some more powerful. Save money by buying your own PVC Pipe (JM Eagle brand 1/2" ID PVC pipe is recommended) from a hardware store such as Home Depot. Some adjustment to other brands of pipe may be necessary if used. There may be slight dimensional differences even with the recommended brand pipe. It is suggested to take one base fitting and verify pipe fit prior to purchasing the pipe. There will be no pipe sent with these fittings.The pictures provided of assembled pyramids are for pictorial demonstration only- no pipe for construction or finished pyramid will be supplied. Depending on the size of the pyramid you want to construct (any size pyramid may be constructed) the lateral edge that starts from the base tip to the apex/cap tip and is calculated using a Phi ratio of 1.6935 multiplied by the base length. (For example and shown in the provided pictures, if your desired base is 12" square you would multiply 12" X 1.6935 = 20.322" Inches – (round this number to 20 3/8” for ease of measurement) From this calculation you will need 4 pieces of ½” PVC pipe 20 3/8” (rounded for ease of measurement) long and 4 pieces of ½” PVC pipe 12" long. Before you run out and cut some pipe there is an additional set of steps required when using these particular fittings to obtain an accurate pyramid structure as shown in the detail pictures. These are as follows: 1. Take each calculated base length (12”) of PVC pipe and subtract 3 1/2” from the initial 12” base piece then cut to this length. This will provide four base pieces with an actual finished length of 8 ½” each.2. Take each calculated lateral piece (20 3/8”) and subtract 5.49” – (round to 5 1/2” for ease of measurement.) This will provide four lateral pieces with an actual finished length of 14 7/8. The adjustments of the pipe lengths detailed above allow for an exact, very accurate pyramid construction that will account for the added material of the base fittings and the apex piece height. This centers the calculated geometric lines of the pyramid to the construction material center line(s). The fittings for this pyramid are a snug press/slide fit for assembly and are very stable without gluing them permanently in place. This design eliminates set screws to tighten the pipe to the fittings and still allows for dismantling your pyramid for movement when desired. If a permanent structure is required, one may use “GOOP” brand adhesive or similar glue to fix the pieces permanently in place. In addition to the above, there are several added design features that are contained within this set of fittings: - An ability to place legs or extensions into the bottom of each base fitting will allow the user to elevate the pyramid to a chosen height while maintaining the pyramid angles and lines. (no pipe is provided for this function) - Alternatively, added extensions can be placed into the ground to anchor the pyramid against wind or other disturbances that may move it around when used outdoors. - The base fittings can be used as cross member support extensions for any pyramid size that needs cross support structure due to size and to eliminate pipe sagging. (additional set(s) of fittings will need to be purchased for this function)- The apex has a removeable capstone with a hidden chamber below to place an object within such as a crystal, shungite, miniature tensor ring, or anything else that fits and suits your need. TIP: If you want to remove the ink lettering on the pipe you acquire, the easiest method is with a paper towel or cloth rag using acetone and wiping it off. Be sure to do this outdoors or with plenty of ventilation as the acetone surely will offend your nose.1/2" to 3/4" PVC pipe adapters are available here: https://www.ebay.com/itm/264921506062Should you require more pyramid connector sets than are currently listed for sale, please make contact to arrange for the quantity you need.If you would like to be able to purchase individual components such as only the Apex - please ask. I can provide whatever parts you need for a nominal cost with free shipping. All parts supplied are proudly manufactured in the USA.All international customers please be advised. This product is offered for sale to international buyers however the product is manufactured in the USA and does not fit most forms of pipe provided within countries outside the USA. Adjustment will be needed to whatever fit you get with international pipe to work with this product.
Price: 32.5 USD
Location: Camarillo, California
End Time: 2024-03-02T04:33:58.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
