SpeedyBee F405 V3 50A Stack FC ECS BMI270 30x30 Flight Controller BLS 50A 4-in-1

Description: Specifications Product Name SpeedyBee F405 V3 30x30 Flight Controller MCU STM32F405 IMU(Gyro) BMI270 USB Port Type Type-C Barometer Built-in OSD Chip AT7456E chip BLE Bluetooth-compatible Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI Not supported for DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering. 6-pin for DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/for DJI Air Unit V1, no wire is needed to be changed. Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store. BetaFlight Camera Control Pad Yes(CC pad on the front side) Current Sensor Input Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0. Power Input 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side) 5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A. 9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A. 3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load. 4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal M1 - M4 on bottom side and M5-M8 on front side. UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6 ESC Telemetry UART R5(UART5) I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware. Buzzer BZ+ and BZ- pad used for 5V Buzzer BOOT Button Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. RSSI Input Supported. Named as RS on the front side. Smart Port / F.Port Not supported Supported Flight Controller Firmware BetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.) Firmware Target Name SPEEDYBEEF405V3 Mounting 30.5 x 30.5mm( 4mm hole diameter) Dimension 41.6(L) x 39.4(W) x 7.8(H)mm Weight 9.6g Product Name SpeedyBee BLS 50A 30x30 4-in-1 ESC Firmware BLHeli_S JH50 Wireless Configuration Full Configuration Supported in the SpeedyBee app PC Configurator Download Link https://esc-configurator.com/ Continuous Current 50A * 4 Burst Current 55A(5seconds) TVS Protective diode Yes External Capacitor 1000uF Low ESR Capacitor(In the package) ESC Protocol DSHOT300/600 Power Input 3-6S LiPo Power Output VBAT Current Sensor Support (Scale=386 Offset=0) ESC Telemetry Not supported Mounting 30.5 x 30.5mm( 4mm hole diameter) Dimension 45.6(L) * 44(W) * 6.1mm(H) Weight 13.8g Thank you for you choose our product , we are trustworthy ,if you have any questions ,please message us freely , we would like to try our best to solve your issue .

Price: 55.44 USD

Location: 深圳

End Time: 2024-12-24T10:17:01.000Z

Shipping Cost: 0 USD